Publications

2021 - Publication

  • B. Rama Krishna, M.V.S. Murali Krishna and P. Usha Sri “Influence of injection pressure on exhaust emissions of insulated diesel engine fuelled with biogas and biodiesel”, International Journal of Mechanical Engineering and Technology (IJMET), Volume 12, Issue 7, July 2021, pp. 23-32.
  • B. Rama Krishna, M.V.S. Murali Krishna and P. Usha Sri “Experimental investigations on exahust emissions of diesel engine fuelled with biogas”, International Journal of Mechanical Engineering and Technology (IJMET), Volume 12, Issue 7, July 2021, pp. 1-9.
  • KandariLowkya, P. Usha Sri “Hydraulic Draft Tube Performance With Varying Geometric Configurations”International Research Journal of Engineering and Technology (IRJET) Volume 8, Issue 6,  June 2021, https://www.irjet.net/volume8-issue6,  S.No: 291
  • P. Yagnasri, N. Seetharamaiah and P. Usha Sri Magnetorheological “Performance of Nano Magnetorheological (MR) Fluid Based on NiFe2O4 Nanoparticles” Nano World Journal, Volume 7, issue 1, April 2021
  • JagadeshwarKandula, P. Usha Sri, Ravinder Reddy. P, S.K.Gugulothu. Numerical and experimental evaluation of near wake cavitation flow around axisymmetric cavitators., Ships and offshore Structures, Taylor & Francis, 03 Mar 2021.
  • Ravi Gugulothu, NarsimhuluSanke, Farid Ahmed, Naga Sarada, M.T. Naik, "Numerical study of Shell and Tube Heat Exchanger Parameters", 1st International Conference on Applied Analysis Computation And Mathematical  Modelling In Engineering (AACMME-2021), National Institute of Technology, Rourkela, February 24-26, 2021.
  • Ravi Gugulothu, NarsimhuluSanke, SahithNagadesi, RatnaKumariJilugu "Thermal hydraulic performance of helical baffle shell and tube heat exchanger using RSM Method", 1st International Conference on Applied Analysis Computation And Mathematical  Modelling In Engineering (AACMME-2021), National Institute of Technology, Rourkela, February 24-26, 2021.
  • BaluNaik, NarsimhuluSanke, “The performance of Combustion Ignition engine by using bio-diesel from animal fat with proportions” International conference on Robotics and Intelligent Manufacturing (ICRIM-2021), St.Martin’s Engineering College, Hyderabad, July 16-17, 2021.
  • ZeradamYeshiwas  and ArkantiKrishnaiah, Numerical Simulations and Experimental Studies on the Formability of Drawing Quality Steel in Single Point Incremental Forming, Journal of Mechanical Engineering, Vol 18(1), 137-156, 2021
  • L. Siva Rama Krishna, P.J. Srikanth, “Evaluation of environmental impact of additive and subtractive manufacturing processes for sustainable manufacturing” Materials Today: Proceedings, Elsevier Publications, Volume 45, Part 2, 2021, Pages 3054-3060. https://doi.org/10.1016/j.matpr.2020.12.060

2020 - Publication

  • ZeradamYeshiwas  and ArkantiKrishnaiah, Extraction of Coordinate Points for the Numerical Simulation of Single Point Incremental Forming Using Microsoft Excel, Springer Nature Switzerland AG 2020, 579–588, https://doi.org/10.1007/978-3-030-24314-2_69. 
  • ZeradamYeshiwas  and ArkantiKrishnaiah, Spiral Tool path Definition and G-code Generation for Single Point Incremental Forming, Journal of Mechanical Engineering, Vol 17(1), 91-102, 2020.
  • ZeradamYeshiwas  and ArkantiKrishnaiah, Numerical Simulation and Experimental Validation of Thickness Distribution in Single Point Incremental Forming for Drawing Quality Steel, International Journal of Applied Engineering, Volume 15, Number 1 (2020) pp. 101-107.
  • ZeradamYeshiwas  and ArkantiKrishnaiah, Effect Of Toolpath Strategy And Tool Rotation On Formability In Single Point Incremental Forming, International Journal of Mechanical and Production Engineering Research and Development, Vol. 10, Issue 3, Jun 2020, 15889-15902.
  • MalothuRamulu and ArkantiKrishnaiah,  Numerical Simulation of Channel Angles and Their Combination Influence on Plastic  Deformation Behaviour of Pure Al Processed by Equal Channel Angular Pressing, Advances in Simulation, Product Design and Development, Lecture Notes on Multidisciplinary Industrial Engineering, Springer Nature Singapore Pte Ltd. 2020, Chapter 36, 451-458, (2020). https://doi.org/10.1007/978-981-32-9487-5_36.
  • M Balu, n. V. Srinivasulu, R. Rajendra&, Azmeeraramesh “Effect of ply orientation on a carbon fiber composite angular beam manufacturing” International Journal of Mechanical and Production Engineering Research and Development (IJMPERD) ISSN(P): 2249–6890; ISSN(E): 2249–8001; Vol. 10, Issue 2, Apr 2020, 615–624
  • BaluMaloth, N.V. Srinivasulu, R. Rajendra“Influence of titanium oxide fillers on the tensile and flexural properties of E-glass fabric/epoxy composites” Materials Today: Proceedings 27 (2020) 1073–1078
  • M.Nirish, R.Rajendra “Suitability of Metal Additive Manufacturing Processes for Part Topology Optimization – A comparative Study, 27(2020) pp: 1601-1607, Springer Proceedings in Materials 8,  Advances in Lightweigt Materials and structures, Ed. A Praveen Kumar et al (Eds.)  © springer Nature Singapore Pte. Ltd 2020.
  • Balu, M, N V Sriniivaalusu, RegaRajendra “Fabrication and characterization of E-glass Fabric composite using Amine-Terminated Butadience Acrylonitrile”,  ©Springerr nature Singapore Pte Ltd, 2020,  Praveen Kumar et. Al (eds.). Advances in Lightweight Materials and structures Springer Proceedings in Materials 8, http:// doi.org/10.1007/978-91-15-7827-4_40
  • JagadeshwarKandula , Usha Sri P , Ravinder Reddy P & S.K. Gugulothu “Experimental investigation of near-wake characteristics of hydrodynamic cavitating flow around circular cylindrical pins of different geometries with and without ultrasonic transducers”, Advances In Materials And Processing Technologies, Dec 2020 Taylor & Francis.
  • G. Sayanna, M.V.S. Murali Krishna and P. Usha Sri “Experimental Investigations on Injection Timing Variation at an Injector Opening Pressure of 190bar on Semi- Adiabatic Diesel Engine with Exhaust Gas Recirculation”, International Journal of Mechanical Engineering and Technology (IJMET), Volume 11, Issue 10, October 2020, pp. 19-27
  • JagadeshwarKandula, P. Usha Sri , P. Ravinder Reddy and S.K. Gugulothu, “Numerical and experimental cavitation assessment of near-wake characteristics of hydrodynamic performance characteristics of cavitating flow with and without ultrasonic transducers”, Journal of Measurement, ELSEVIER, November 2020
  • C. HariVenkateswara Rao, P. Usha Sri and R. Ramanarayanan, “CFD Simulation Study on Shell Made of Composite Material when Subject to Temperatures Above 3000 Degrees Centigrade”Journal of New Developments in Chemistry Vol-3, Issue-1, pp. 32-40
  • G. Sayanna, M.V.S. Murali Krishna, P. Usha Sri and M. Ravi Chandra, “Experimental Investigations on Exhaust Emissions of semi- Adiabatic Diesel Engine with Exhaust Gas Recirculation” Journal of Pollution Research Vol.39(3):2020 pp. 685–691
  • G. Sayanna, M.V.S. Murali Krishna and P. Usha Sri “Experimental Investigations on Semiadiabatic Diesel Engine With Exhaust Gas Recirculation Fuelled withTamarind Boidiesel” International Journal of Production Technology and Management (IJPTM) Volume 11, Issue 1, January-June, 2020, pp. 8–21, Article ID: IJPTM_11_01_002 Journal Impact Factor (2019): 7.2150
  • Leela Prasad N., Usha Sri P., Vizayakumar K. (2020) Life Cycle Assessment of a 100 kWp Solar PV-Based Electric Power Generation System in India. In: Narasimham G., Babu A., Reddy S., Dhanasekaran R. (eds) Recent Trends in Mechanical Engineering. Pages 81-94. Lecture Notes in Mechanical Engineering. Springer, Singapore. https://doi.org/10.1007/ 978-981-15-1124-0_7.
  • Siva Rama Krishna L., Vanapalli S.D., Venkatesh S., Potturi A, “Orbital Volume Analysis of Midfacial Fractures Using Additive Manufacturing Technologies”. Learning and Analytics in Intelligent Systems, vol 2. Springer, Cham, pp. 559-567, 2020. 
  • Siva Rama Krishna L., Balasany U.K., Venkatesh S.R., Potturi A, “Assessment of Dimensional Accuracy of Reproducibility of Cadaver Skull by FDM Additive Manufacturing” Learning and Analytics in Intelligent Systems, Vol.2, Springer Cham, pp. 662-672, 2020. 3. 
  • P. Narsimha, L. Siva Rama Krishna, P. VenkataRamana, “Influence of Welding Process and Weld Design on The Mechanical Properties of Reduced Activation Ferritic-Martensitic Steel Weldments” International Journal of Scientific & Technology Research Volume 9, Issue 04, April 2020. Impact Factor = 0.28. Indexed in Cross Reference & Scopus. 
  • Mahipal Reddy, L. Siva Rama Krishna, S. Sharath Kumar and P. Ravinder Reddy, “A Comparative Study on Performance of 3D-Printed EDM Electrode with Conventional EDM Electrode” Recent Trends in Mechanical Engineering, Lecture Notes in Mechanical Engineering, Springer Nature Singapore, Jan 2020. https://doi.org/10.1007/978-981-15-1124-0_19
  • E. MadhusudhanRaju, L. Siva Rama Krishna, V. Nageswara Rao, Y. Sharath Chandra (2015), “Effect of Link Flexibility on tip position of a single link robotic arm”, Journal of Physics: Conference Series 662 (2015), IOP Publishing.  012020, doi:10.1088/issn.1742-6596. Online ISSN: 1742-6596 Print ISSN: 1742-6588. 
  • Vishnu PramodTeja G., Saraswathamma K., Padmalatha T.S.R.V. (2020) Machining Characteristics of Electro Discharge Machining on NIMONIC 80A by Response Surface Methodology. In: Satapathy S., Raju K., Molugaram K., Krishnaiah A., Tsihrintzis G. (eds) International Conference on Emerging Trends in Engineering (ICETE). Learning and Analytics in Intelligent Systems, vol 2. Springer, Cham. https://doi.org/10.1007/978-3-030-24314-2_76
  • Thallapalli N., Balne V.K.G., Padmalatha T.S.R.V. (2020) Modelling of Surface Roughness and Tool Wear Rate During Turning of AISI 202 Stainless Steel. In: Satapathy S., Raju K., Molugaram K., Krishnaiah A., Tsihrintzis G. (eds) International Conference on Emerging Trends in Engineering (ICETE). Learning and Analytics in Intelligent Systems, vol 2. Springer, Cham. https://doi.org/10.1007/978-3-030-24314-2_88
  • NagaveniThallapalli, Kishore Kumar Kandi, RenukaBatta, “Investigation on the micro-structure and mechanical properties of copper based surface composites fabricated by friction stir processing” Materials Today: Proceedings, 27(2), pp1774-1779, 2020https://doi.org/10.1016/j.matpr.2020.03.688.
  • ThallapalliNagaveni.,Balne V.K.G., Padmalatha T.S.R.V. (2020) “Modelling of Surface Roughness and Tool Wear Rate During Turning of AISI 202 Stainless Steel” International Conference on Emerging Trends in Engineering (ICETE). Learning and Analytics in Intelligent Systems, vol 2. (pp748-756) Springer, Cham.https://doi.org/10.1007/978-3-030-24314-2_88.
  • ThallapalliNagaveni.,Balne V.K.G., Padmalatha T.S.R.V. (2020) “Modelling of Surface Roughness and Tool Wear Rate During Turning of AISI 202 Stainless Steel” International Conference on Emerging Trends in Engineering (ICETE). Learning and Analytics in Intelligent Systems, vol 2. (pp748-756) Springer, Cham.https://doi.org/10.1007/978-3-030-24314-2_88.
  • Kandi K.K., ThallapalliNagaveni., Sunder M., Vuda R. (2020) Design and Analysis of Cap Forward Armrest Component. In: Praveen Kumar A., Dirgantara T., Krishna P.V. (eds) Advances in Lightweight Materials and Structures. Springer Proceedings in Materials, vol 8 pp 145-153. Springer, Singapore. https://doi.org/10.1007/978-981-15-7827-4_14
  • S.Charvani, Ch.Gopal Reddy, G.Narendar, SEM, XRD and TGA Study of Alumina Nanocomposites,  AIP Conference Proceedings 2297 (020025) (2020) 1-9.
  • G.Narendar, Investigation on Natural Circulation Loop with Band Heater and Nanofluid as Loop Fluid, Sambodhi(UGC Care Journal) 43(03)  (2020) 81-87
  • G Vishnu PramodTeja, K. Saraswathamma, P. Murali Krishna, G. Tejeswara Rao, “Experimental Investigation of Electro Discharge Machining on NIMONIC 80A through Response Surface Methodology”, Advances in Applied Mechanical Engineering, Lecture Notes in Mechanical Engineering. Springer, Singapore, 2020, 991-1000.
  • Ravi Gugulothu, NarsimhuluSanke, Farid Ahmed, RatnaKumariJilugu, Book Chapter 25 "Numerical Study on Shell and Tube Heat Exchanger with Segmental Baffle",  Algorithms for Intelligent Systems, Proceedings of International Joint Conference on Advances in Computational Intelligence, IJCACI 2020, Springer, ISSN 2524-7573 (electronic), ISBN 978-981-16-0586-4 (eBook), https://doi.org/10.1007/978-981-16-0586-4
  • VenkatRamana G, NarsimhuluSanke, "Evaluation of Tensile and Microstructure properties of AA2014 and AA7075 FSW weld-ments developed by HSS-10%Co and WC tools" ICMMSE_2020, Science Direct, ELSEVIER

2019 - Publications

  • Garimella Sridhar, Ramesh Babu, P., “Effect of cutting parameters on machining induced distortion in thin wall thin floor parts” Journal of Mechanical Engineering, 2019, 17-27.
  • U. Ashok Kumar, M. Prakash, P. Laxminarayana, “Effect of Material Removal Rate on Micro Hole Machining using Die Sinker EDM” Procedings of Conference on Electrophysical Machining In Modern Industry - International scientific-practical conference of young scientists, graduate students and students December 18–20, 2018,At: Perm, Russia, ISBN 978-5-398-02132-5 © PNRPU, 2019.
  • M Swamy, P Laxminarayana, AHV Pavan, MC Antony Harison, G Jayaraman, K Singh, “Microstructural characterization and mechanical properties of sand cast and investment cast alloy 625 for HP/IP casing applications for advanced fossil fired power plants”, Volume 5, Issue 13, Part 3, 2018, Pages 27118-27122, Materials Today: Proceedings https://doi.org/10.1016/j.matpr.2018.09.019.
  • Malothu Ramulu and Arkanti Krishnaiah, The Effect of Die Channel Angles and their Combination on Plastic Deformation of Pure Copper During Equal Channel Angular Pressing Using Finite Element Modelling, Advanced Engineering Forum, Trans Tech Publications, Switzerland, Vol. 31, February, 2019, 63-69.
  • B.Hadya., et al. Presented paper entitled: “Evaluation and Impacts on Mechanical Behaviour of Friction Stir Welded Copper 2200 Alloy”, International  National Conferences on “Innovations in Mechanical Engineering”(IVIME-2019) 4th &5th  January , 2019 held at Guru Nanak Institutions, Ibrahimpatnam, Telangana state.India.
  • Mithun Kasturi, Saraswathamma K, Dhanesh Kant Verma “Effect of Post Weld Heat Treatment Soaking Time on Microstructure and Mechanical Properties of TIG Welded Grade 91 Steel” Journal of Metals, Materials and Minerals, Vo.29, No.2 (2019), 42-50.
  • Venakata Satyanarayanaraju chetlapalli , Rahul Dixit,  Bonagiri Pydiraju, Saraswathamma konapalli, Uddemarry ramakrishna, Palanki sai pavan “Effect of Corrosion Protection Plating on the Magnetic and Corrosion Properties of Cobalt-Iron-Vanadium (48-48-2) Soft Magnetic Materials”  Journal of Magnetism and Magnetic Materials:  under review
  • L.Siva Rama Krishna, Shiva DharshanVanapalli, Abhinandan Potturi, “Orbital Volume Analysis of Midfacial fractures using Additive Manufacturing Technologies“ in the International Conference on Emerging Trends in Engineering (ICETE 2019) organised by OUCE alumini association in association with Springer during 22-23 March, 2019.
  • L Siva Rama Krishna, Balasany Uday Kumar, Sri Ram Venkatesh and Potturi Abhinandan, “Assessment of Dimensional Accuracy of Reproducibility of Cadaver Skull by FDM Additive Manufacturing”, in the International Conference on Emerging Trends in Engineering (ICETE 2019) organised by OUCE alumini association in association with Springer during 22-23 March, 2019.
  • G.Narendar, J.Vijay Kumar, CFD Study of Fluid Flow Through Pipe with Different Types of Ribs, International Journal of Scientific Research and Review, ISSN NO: 2279-543X, Volume 8, Issue 1 , 2019 PP
  • G.Narendar, J. Narsingrao, CFD Analysis of Gas Turbine Blade Cooling With Staggered Holes, International Journal of Scientific Research and Review, Volume 8, Issue 1, 2019, ISSN NO: 2279-543X, PP 756-765
  • G. Narendar,G. Venod , CFD Analysis on Impeller Passage of Centrifugal Pump, International Journal of Modern Engineering and Research Technology, Volume 6, Issue 1, January 2019 ISSN: 2348-8565, PP 16-27
  • G.Narendar , M.Ramrao , CFD Acoustic Analysis Of Combustor With Porous Insert Dampers In A Gas Turbine,  International Journal for Research in Engineering Application & Management ISSN : 2454-9150 Vol-04, Issue-10, Jan 2019, 373-377
  • G.Narendar, P.SaiSrikar, Design and Fabrication of Press Tool for Manufacturing Body of Carriage Box used For Military Applications, International Journal of Scientific Research and Review, Volume 8, Issue 3,  2019, ISSN NO: 2279543X, PP 1-10
  • K.L.Uday Kiran,  Sanar Zuhair Abbas,  K.Saraswathamma,  G.Chandra Mohan Reddy, A.M.K.Prasad,  “Parametric optimization during wire EDM taper cutting on AISI D2 steel using desirability function”, International Conference on Emerging Trends in Engineering (ICETE), 22-23 March 2019, University College of Engineering (A), Osmania University..
  • K.L.Uday Kiran, G. Chandra Mohan Reddy, A.M.K.Prasad, “ Study on Effect of process parameters on angular error and Cutting speed in wire-EDM taper cutting”,  International Journal for Research in Engineering Application & Management (IJREAM), ISSN : 2454-9150 ,Vol-04, Issue-10, Jan 2019.
  • M.Prakash, Harika, P. Laxminarayana “Micro drilling of glass fiber reinforced polymer composites” published at international journal of research in application applied science and engineering technology (IJRASET), volume 7 issue V may 2019.

2018 - Publications

  • Goitom Tesfaye, Rega Rajendra, “Sampling strategy of Free-form using Coordinate measuring machine surface,”Mechanical Engineering for sustainable Development: State of the Art Research, CRC press, January 2018. (ISBN hard: 978-1-77188-681-9.)
  • Goitom Tesfaye, Rega Rajendra, An Artefact Based Continues Performance Evaluation of CMM, 7th Intl. and 28th All India Manuf. Technology, Design And Research Conf. 2018 (AIMTDR 2018). (Submitted), Chennai, 17-20 March 2018
  • V Uma Maheshwar, Vijrumbana, Analysis of Key Design Parameters of a Pure Scramjet Engine to Reduce its Starting Mach Number, International Journal of Modern Engineering and Research Technology. Volume 5 | Special Issue | June 2018
  • V. Uma Maheshwar, Moogi Srinivasa Rao | Hyderaba,Comparative Study of Structured and Unstructured Meshing of Nozzle Model,  International Journal of Modern Engineering and Research Technology. Volume 5 | Special Issue | June 2018
  • V. Uma Maheshwar, “Computational Study of Savonius Vertical Axis Wind Turbine (VAWT) for Different Overlap Ratios”, International Journal of Modern Engineering and Research Technology. Volume 5 | Special Issue | June 2018
  • V. Uma Maheshwar, Pavan Mummadi, International Journal of Modern Engineering and Research Technology. Volume 5 | Special Issue | June 2018
  • K.L.Uday Kiran, K.Saraswathamma, G. Chandra Mohan Reddy, A.M.K.Prasad, “Effect of Process Parameters on Angular Error in Wire-EDM Taper Cutting of AISI D2 Tool Steel”, International Journal of Engineering Science Invention (IJESI) ISSN (Online): 2319 – 6734, ISSN (Print): 2319 – 6726 www.ijesi.org ||Volume 7 Issue 6 Ver IV || June 2018 || PP 67-72.
  • Jeevan Kumar, N. and Ramesh Babu, P “Analysis of Mode I and Mode II Crack Growth Arrest Mechanism with Z-Fibre Pins in Composite Laminated Joint” Applied Composite Materials (2018) 25:365–379
  • Nagarjuna M, Dr. Gajanana S and Dr. Krishnaiah, Investigation to Optimize Process     Parameters on Mechanical Properties of Aluminium Alloy in Die Casting Using Taguchi     Method, Journal of Manufacturing Technology Today (MTT) (ISSN: 0972-7396), a monthly     technical journal from Central Manufacturing Technology Institute (CMTI), Bangalore, Vol.17, Issue 10, October (2018) 19-27.
  • Nagarjuna M, Dr. Gajanana S and Dr. Krishnaiah, Experimental investigations of Mechanical Properties of Al 7178 Metal Matrix Reinforced with Silicon Carbide, International Journal for Research in Engineering Applications and Management, Vol.9, Issue 4, December, 2018.
  • G. Madhusudhan Reddy, M. S. R. Prasad, A. Krishnaiah, P. Ramesh Babu, Editorial Preface: A Special Issue on Advances in Materials and Manufacturing, Materials Today: Proceedings, Volume 5, Issue 13, Part 3, 2018, Pages 26793-26798.
  • D Srinivas Rao, Krishanaiah A, Y Krishn, Syed Adil, Optimization of Cutting Parameters for Improvement in the Machining Performance on Fe-Al Mechanical Alloy, Materials Today: Proceedings 5 (2018) 27193–27198.
  • M. Ravi Kumar, A. Krishnaiah and Ravi Shankar, KalvacExperimental Study on Micro Machining of SS304 by Using Electric Discharge Machining, Materials Today: Proceedings 5 (2018) 27269–27276.
  • K. Buschaiah, M. JagadeeswaraRao, A. Krishnaiah, Investigation On The Influence Of Edm Parameters On Machining Characteristics For AISI 304, 5 (2018) 3648-3656.
  • PavanKumar Thimmaraju, Krishnaiah Arkanti, G. Chandra Mohan Reddy, Parametric Analysis of Friction Stir Welding Process, 5 (2018) 26981-2698
  • Dr.B.Hadya, et al. Published a paper, Title “Experimental Study on AA7075 Its Effect of Rotational Speed and Tool Pin Profile on Friction Stir Welding Process” in the International Journal of Innovations in Engineering and Technology (IJIET), Volume 9 Issue 3, pp: 88-93, February 2018.
  • B. Venugopal Rao,   N. Aravindan,   K. Saraswathamma, “Experimentation of effect of process parameters on mechanical properties in SAW Process” Materials Today: Proceedings, Vol.5 , Issue 13, Part 3 (2018) 26961-26967.
  • KL Uday Kiran, P Sarath, K Saraswathamma, G Chandra Mohan Reddy “Prediction of Angular Error in wire EDM taper cutting of AISI D2 tool Steel by RSM approach” Materials Today: Proceedings, Vol.5 , Issue 13, Part 3 (2018) 27043-27050.
  • K. L. Uday Kiran, K Saraswathamma, A.M.K.Prasad, G.Chandra Mohan Reddy, “Effect of process parameters on angular error in wire-EDM taper cutting of AISI D2 tool steel” , International Journal of Engineering and Science Invention (IJESI),Vol .7, Issue 1 (2018), 7883.
  • L.Siva Rama Krishna, Sandeep boddepalli, Sriram Venkatesh, “Topology Optimization of Aircraft Bearing Bracket and Prototype Manufacturing Using 3D Printing“ National  Conference on “Large Scale Multidisciplinary Systems of National  Significance Trends & Challenges” (LAMSYS 2018) organised by ISRO-ISSE Sriharikota – Chennai chapter in association with Sathyabhama  Institute of Science and Technology during 20 – 21, April 2018
  • Ramarao M, B Nageswara Rao,  G Narendar, Combustion Acoustics Analysis of Gas Turbine Using CFD Package, International Journal of Engineering Technology Science and Research,ISSN 2394 – 3386, Volume 5, Issue 5, May 2018 pp 251-255
  • G.Narendar, E. Arjun, Experimental Investigation on Delamination of Nanocomposite Laminates, Journal of Engineering Research and Application ISSN : 2248-9622, Vol. 8, Issue 6 (Part -V) June 2018, pp 46-49
  • S.Charvani, S.Shravan Kumar Reddy, G.Narendar, Ch.Gopal Reddy, Preparation characterisation of alumina nanocomposites, Materials Today: Proceedings 5 (2018) 26817–26822
  • G.Narendar , T.Ravinder Goude, Influence of Geometrical Parameters on the Performance of Plate Fin-Tube Heat Exchanger, International Journal of Scientific Research and Review, ISSN NO: 2279-543X, Volume 7, Issue 12, 2018, PP 704-714
  • G.Narendar, E. Arjun, Finite Element Analysis of Delamination of Nanocomposites, International Journal of Scientific Research and Review, ISSN NO: 2279-543X, Volume 7, Issue 12, 2018 PP 715-721
  • K. L. Uday Kiran, T Nagaveni , K. Saraswathamma, AMK. Prasad, G. Chandra Mohan Reddy, ―Multi-objective optimization of WEDM process parameters for taper cutting of AISI D2 tool steel‖ International Journal of Engineering Technology 7 (4-5) (2018) 703706.(scopus indexed)
  • K. L. Uday Kiran, K. Saraswathamma, AMK. Prasad , G. Chandra Mohan Reddy, “Prediction of Angular Error and Surface Roughness in Wire-EDM Taper cutting of AISI D2 Tool Steel”, International Journal of Modern Engineering and Research Technology Volume 5 | Special Issue | June 2018.
  • K.L.Uday Kirana, P.Sarath, K.Saraswathamma, G.Chandra Mohan Reddy, “Prediction of angular error in wire-EDM taper cutting of AISI D2 tool steel by RSM approach”, Materials Today: Proceedings 5 (2018) 27043–27050.
  • U.Ashok Kumar, Prof. P. Laxminarayana “Optimization of Electrode Tool Wear in micro holes machining by Die Sinker EDM using Taguchi Approach, Elsevier - Materials Today: Proceedings 1824-1831 Volume 5, Issue 1, Part 1,  Pages 1824-1831, 2018. .https://doi.org/10.1016/j.matpr.2017.11.281
  • U.Ashok Kumar, Prof. P. Laxminarayana “Experimental optimisation of process parameters on micro hole machining by Die sinker EDM - International journal of Advanced Materials Manufacturing & Characterization (IJAMMC),Volume 8 , Issue 2 , 2018.

2017 – Publications

  • Jeevan Kumar, N. and Ramesh Babu, P.” Impact analysis of embedded delamination growth in stiffener of hybrid laminated composite stiffened panel” International Journal of Computational Materials Science and Engineering, Vol. 6, No. 1 (2017) 1750001
  • S.V.Prasad, P. Laxminarayana, P.Ravinder Reddy” Influence Of Tool Angles Of Endmill On Distortion Of  2014a T651 Aluminum Alloy During Machining”, IJRET: International Journal of Research in Engineering and Technology, Volume: 06 Issue: 06 , pp33-38, June-2017 . eISSN: 2319-1163 pISSN: 2321-7308
  • S.V.Prasad, P. Laxminarayana, P.Ravinder Reddy “Influence of Tool Coatings on Distortion of 2014A T651 Aluminum Alloy during Machining”, International Journal of Innovative Research in Science, Engineering and Technology, Vol. 6, Issue 10,pp 20192-20199, October 2017, DOI:10.15680/IJIRSET.2017.0610028
  • Mohammed Viquar Mohiuddin, Syed FerhathullahHussainy, Arkanti Krishnaiah, P Laxminarayana, “Experimental investigation to produce thin-walled sand casting using combination of casting simulation and additive manufacturing techniques” June 2017, Volume 90, Issue 9–12, pp 3147–3157, The International Journal of Advanced Manufacturing Technology,Springer,DOI 10.1007/s00170-016-9653-6.
  • S Viswanaath, J Hayavadana, P Laxminarayana, Ayodya Kavitha, K Sreenu, “Novel Methods of Assessment of Aesthetic Properties of Dress Material” Volume 6; Issue 7; July 2017; Page No. 4758-4763, International Journal of Current Advanced Research,ISSN: O: 2319-6475, ISSN: P: 2319 – 6505, Impact Factor: SJIF: 5.995, DOI: http://dx.doi.org/10.24327/ijcar.2017.4763.0577.
  • Syed Azeem Pasha, Ravinder Reddy, P Laxminarayana “Electric Discharge Machining Characteristics of AA7075/MWCNT Surface MMCs Fabricated through Friction Stir Processing”6th International & 27th  All India Manufacturing Technology, Design and Research Conference (AIMTDR-2016), ISBN: 978-93-86256-27-0
  • M. Naveen Kumar, Sriram Venkatesh, M. Manzoor Hussain; Influence of 3D material Properties on Quality Prototypes Using SLS and FDM Process of a 3D Printer; International Journal of Current Engineering and  Technology; Vol.7 No.3 June 2017; E-ISSN 2277-4106, P-2347-5161.
  • S.H.Rahul, K.Balasubramanian, Sriram Venkatesh, Optimizing Inkjet Printing  Process to Fabricate Thick Ceramic Coatings, Ceramics International 43 (2017) 4513- 4519, Elsevier. Contents available at ScienceDirect.
  • M. Naveen Kumar, Sriram Venkatesh, M. Manzoor Hussain; Investigation of run out of Polyamide parts in Selective Laser Sintering Process using Taguchi Method; ISSN: 2348-3733; Vol. 4, Issue 10, Oct. 2017.
  • M. Naveen Kumar, Sriram Venkatesh, M. Manzoor Hussain; Experimental Investigation on Concentricity of Polyamide Sintered Prototypes by Selective Laser Sintering Process using Taguchi Method; IMPACT: International Journal of Research in Engineering and Technology; ISSN (P): 2347-4599; ISSN (E): 2321-8843;  Vol. 5, Issue 11, Nov. 2017, 25-34.
  • M. Naveen Kumar, Sriram Venkatesh, M. Manzoor Hussain; Experimental Investigations on Influence of Process Parameters in Selective Laser Sintering using Taguchi Method; International Journal of Mechanical and Production Engineering Research and Development(IJMPERD); ISSN (P): 2249-6890; ISSN (E): 2249-8001;  Vol. 7, Issue 6, Dec 2017, 45-52.
  • D Srinivas Rao, A Krishnaiah, Y Krishna, Syed Adil. “Mathematical Modeling using Artificial Neural Networks for Quality Evaluation in the Machining of Fe-Al Alloy with PCBN Tools”. Asian Journal of Convergence in Technology (AJCT), Volume 3, Issue 3, December 2017.
  • D Srinivas Rao, A Krishnaiah, Y Krishna, Syed Adil. “Modeling of Machining Performance on Fe-Al Alloy using Artificial Neural Networks”. International Journal of Engineering Technology Science and Research (IJETSR). Volume4, Issue 11, November 2017
  • D. S. Rao, A. Krishnaiah, Y. Krishna and S. Adil, "Optimization of Cutting Parameters for Improved Machining of Fe-Al alloy," Published in IEEE Xplore Digital Library on December 21, 2017, pp. 1203-1206. 
  • D Srinivas Rao, A Krishnaiah, Y Krishna, Syed Adil. “Sustainable Machining of Fe-Al Mechanical Alloy using PCBN Tool Inserts”. International Journal of Engineering Research in Mechanical and Civil Engineering (IJERMCE).Volume 2, Issue 3, March 2017.
  • P. S. Ravi, A. Krishnaiah, Md. Azizuddin, Suresh Akella, Design and Experimentation of Roll Bond Evaporator for Room Air Conditioner with R-22 as Refrigerant, International Journal of Engineering, IJE TRANSACTIONS A: Basics Vol. 30, No. 4, (April 2017) 558-566.
  • Goitom Tesfaye, Rega Rajendra, Sampling strategy of Free-form using Coordinate measuring machine surface, Indian Society of Mechanical Engineers (ISME) 2017, NIT Warangal, India. (Presented)
  • Goitom Tesfaye, Rega Rajendra, Contour Based Adaptive Sampling Strategy of Free-form surface using CMM, Proceeding of COPEN10 2017, IIT Madras Chennai, 915-918.
  • Goitom Tesfaye, RegaRajendra; Global Form Deviation Evaluation of Free-form Surface using Coordinate Measuring Machine. Intl. Jl. of Mechanical and Production Engineering Research and Development, Vol. 7(6), 525-532, 2017. (Scopus indexed)
  • Goitom Tesfaye, Ravva Sirinivas, and Rega Rajendra; Equi-parametric Sampling Strategy for Evaluation of Higher Degree Free-form Surface using Contact Measurement. Intl. Jl of Advanced Research in Engineering and Technology, Vol. 8(4), pp. 21–27, 2017. (Scopus indexed)
  • Goitom Tesfaye, T.S.S Prasad, Rega Rajendra; Isoparametric line Sampling Strategy for Evaluation of Lower Degree Free form surface using Contact Measurement. Intl. Jl of Engineering and Manufacturing Science, Vol. 7(2), pp. 171-180, 2017. (UGC Recognized journal)
  • Goitom Tesfaye, Rega Rajendra; Adaptive sampling strategy of Free-form surface using CMM. Indian Academy of Science (Sadhana), Springer.(Communicated)
  • Rega Rajendra, Dilip Kumar Pratihar∗ "Analysis of double support phase of biped robot and multi-objective optimization using genetic algorithm and particle swarm optimization algorithm"¯Sadhana- Indian Academy of Sciences.
  • Dr.B.Hadya, Published a paper, Title: Comparative Study of Thermodynamic Properties of Hydro-Carbon Group Refrigerants in a Vapour Compression Refrigeration System as an Alternative to HCFC-22,   In the Int. J. Mech. Eng. Res. & Tech, ISSN 2454 – 535X, Vol. 3, No. 1, February 2017
  • Dr.B.Hadya, et al. Published a paper, Title Performance Analysis of an Omni directional Intake Duct Wind turbine using CFD, in International Journal of Latest Engineering and Management Research (IJLEMR) ISSN: 2455-4847, Volume 02 - Issue 09, PP. 01-10, September 2017
  • Dr.B.Hadya, et al. Published a paper, Title “Enhancement of Bio-Gas Yield from Dry and Green Leaves by Inoculation, in the International Journal of Latest Engineering and Management Research (IJLEMR) ISSN: 2455-4847, Volume 02 - Issue 10, PP. 07-12, October 2017.
  • TSRV Padmalatha, T Nagaveni, K Saraswathamma, K Chandravathi, “Multi objective optimization Of micro-EDM drilling on Maraging steel by Genetic Algorithm” International Journal of Engineering Science and Technology, Vol. 9 , Issue No.03 (2017), 133-144.
  • TSRV Padmalatha, T Nagaveni, K Saraswathamma, “Optimization of Process Parameters for CNC EDM on OHNS tool steel using Desirability Function”, International Journal of Engineering Science and Technology, Vol. 9 , Issue No.03 (2017), 145-151.
  • TSRV Padmalatha, Madhavi J, K Saraswathamma, “Influence of Process Parameters of Surface Grinding on Maraging Steel” International Journal of Materials Science, Vol.12, Issue No.1 (2017), 127-135.
  • K Saraswathamma, TSRV Padmalatha, “Model for the prediction of surface finish in Ball End Magnetorheological finishing process”, International Journal of Engineering and Technology. Vol 9, No 3 (2017), 1582-1590.
  • K.Saraswathamma, Sunil Jha, P.V. Rao, “Rheological behaviour of Magnetorheological polishing fluid for Si polishing”, Materials Today: Proceedings, Vol.4 , Issue 2, Part A (2017), 1478-1491.
  • B.Laxmi, T.Nagaveni, TSRV Padmalatha , K Saraswathamma, “Influence of tool geometry and process parameters on performance characteristics of EN-19 steel in sink type EDM using Taguchi method” International Journal of Engineering Science and Technology, Vol. 9, No.05(2017), 299-310.
  • K. L Uday Kiran, K Saraswathamma, A.M.K.Prasad, G.Chandra Mohan Reddy, “Study on Wire-EDM Taper Cutting Process: A Review” International Journal of Technical Innovation in Modern Engineering & Science, Vol .3, Issue 12(2017), 268-274.
  • V. Uma Maheshwar, AMK Prasad,Experimental Investigation of Downstream Flow Field in a Linear Turbine Cascade: Effects of Relative Wall Motion, International Journal of Advanced Research in Basic Engineering Sciences and Technology, Volume 2, Special Issue 22 - April 2017, pp.37-49, ISSN 2456- 5717
  • L.Siva Rama Krishna., Natrajan Mahesh, N.Sateesh, “Topology optimization using solid isotropic material with penalization technique for additive manufacturing”,  Materials Today: Proceedings Vol.4, issue 2, pp. 1414–1422, 2017, Elsevier Publications, DOI 10.1016/j.matpr.2017.01.163.
  • G.Narendar, A.V.S.S Kumara Swami Gupta and A.Krishnaiah Experimental investigation on the preparation and applications of Nano fluids, Materials Today: Proceedings 4 (2017) 3926–3931
  • G.Narendar, V.Chandra Sekhar, Preparation and Testing of Composites with Slag and Egg Shell Powder Filler, International  Journal of Engineering Research and Application, ISSN : 2248-9622, Vol. 8, Issue 6 (Part -II) June 2018, 57-60
  • G. Narendar, V. Chandra Sekhar,  Tensile Properties of Fiber Reinforced Epoxy Composites for various Fiber loading and Fiber length, International Journal of Latest Engineering Research and Applications (IJLERA) ISSN: 2455-7137 Volume – 02, Issue – 10, October – 2017, PP – 66-71
  • T.Nagaveni, B.Laxmi, TSRV Padmalatha, K.Saraswathamma, ―Influence of tool geometry and process parameters on performance characterstics of EN-19 steel in sink type EDM using Taguchi method‖International Journal of Engineering Science and Technology, Vol. 9 No.05 May 2017.
  • TSRV Padmalatha, T Nagaveni, K Saraswathamma, ―Optimization of Process Parameters for CNC EDM on OHNS tool steel using Desirability Function‖, International Journal of Engineering Science and Technology, Vol. 9 , Issue No.03 (2017), 145-151.
  • T. Vijaya, S. Ram Mohan Rao, S. Srinu Naik, T. Nagaveni, V.Nanya and M.Nagabhushanam, ―Growth, Characterization, Optical and Vibrational properties of Mg2+ doped Cd0.8Zn0.2S Semiconductor Compounds using Co-Precipitation Method‖ International Journal of Material Sciences and Technology, Volume 7, Number 1 (2017), pp. 1-16
  • TSRV Padmalatha, T Nagaveni, K Chandravathi, K Saraswathamma, ―Multi objective optimization Of micro-EDM drilling on Maraging steel by Genetic Algorithm‖ International Journal of Engineering Science and Technology, Vol. 9 , Issue No.03 (2017), 133-144.
  • T. Nagaveni , ―Design and Analysis of Draw Die for The Tail Gate Skirt Panel‖, International Journal of Technical Innovation in Modern Engineering & Science 3, Issue 10( 2017)
  • TSRV Padmalatha, T Nagaveni, K Chandravathi, K Saraswathamma, “Multi objective optimization Of micro-EDM drilling on Maraging steel by Genetic Algorithm” International Journal of Engineering Science and Technology, Vol. 9 , Issue No.03 (2017), 133-144
  • TSRV Padmalatha, T Nagaveni, K Saraswathamma, “Optimization of Process Parameters for CNC EDM on OHNS tool steel using Desirability Function”, International Journal of Engineering Science and Technology, Vol. 9 , Issue No.03 (2017), 145-151
  • TSRV Padmalatha, Madhavi J, K Saraswathamma, “Influence of Process Parameters of Surface Grinding on Maraging Steel” International Journal of Materials Science, Vol.12, Issue No.1 (2017), 127-135 
  • K Saraswathamma, TSRV Padmalatha “Model for the prediction of surface finish in Ball End Magnetorheological finishing process”, International Journal of Engineering and Technology, Vol 9 No 3 Jun-Jul 2017( Impact factor : 0.18(schimago) & 0.7(RG))
  • B.Laxmi, T.Nagaveni, TSRV Padmalatha, K.Saraswathamma, “Influence of tool geometry and process parameters on performance characterstics of EN-19 steel in sink type EDM using Taguchi method”International Journal of Engineering Science and Technology, Vol. 9 No.05 May 2017
  • K.Buschaiah, A.Parshuramulu and P.Laxminarayana “Influence of Tool Geometry and Performance Characteristics of EN-19 Steel by EDM Using Taguchi Method”, IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE), e-ISSN: 2278-1684, p-ISSN: 2320-334X Vol. 14, Issue 4, Ver. I (Jul-Aug.2017) pp 28-35.
  • Syed Azeem Pasha, Ravinder Reddy P, Laxminarayana P, Buschaiah K “Influence of Process Parameters on Micro hardness of AA7075/MWCNT Surface Composites Fabricated through Friction Stir Processing” International Journal of Innovative Research in Technology (IJIRT), ISSN:2349-6002, Volume 4, Issue 7, Dec.2017, pp 665-670
  • U Ashok Kumar, Prof. P. Laxminarayana, “Study of surface morphology on micro machined surfaces of AISI 316 by Die Sinker EDM”, Materials today: proceedings 12/2017; 4(2):1285-1292., DOI:10.1016/j.matpr.2017.01.149
  • U Ashok Kumar, Prof. P. Laxminarayana , “Study of Tool Wear Optimization in Micro Holes Machining of SS316 by Die Sinker Electrical Discharge Machining”, International Journal of Scientific Research in Multidisciplinary Studies E-ISSN: 2454-9312,Vol.3, Issue.7, pp.1-4, July (2017)
  • U Ashok Kumar, Prof. P. Laxminarayana , “Optimization of process parameters of Material Removal Rate in Micro hole Machining by Die sinker EDM”, IOSR Journal of Engineering (IOSRJEN) (p): 2278-8719,Vol. 07, Issue 07 (July. 2017), Volume1, PP 61-65, ISSN (e): 2250-3021
  • K. L. Uday Kiran , K. Saraswathamma , AMK. Prasad , G. Chandra Mohan Reddy, “Study on Wire-EDM Taper Cutting Process: A Review”, International Journal of Technical Innovation in Modern Engineering & Science (IJTIMES) Impact Factor: 3.45 (SJIF-2015), e-ISSN: 2455-2585 Volume 3, Issue 12, December-2017.
  • U Ashok Kumar, Prof.  P. Laxminarayana "Study of Tool Wear Optimization in Micro Holes Machining of SS316 by Die Sinker Electrical Discharge Machining", International Journal of Scientific Research in Multidisciplinary Studies, Vol.3, Issue.7, pp.1-4, 2017.
  • U Ashok Kumar, Prof. P. Laxminarayana “Optimization of process parameters of Material Removal Rate in Micro hole Machining by Die sinker EDM” , IOSR Journal of Engineering (IOSRJEN), Vol. 07, Issue 07 ||V1|| PP 61-65,  2017.
  • U. Ashok Kumar, Prof.  P. Laxminarayana  “Study of surface morphology on micro machined surfaces of AISI 316 by Die Sinker EDM”  , Elsevier - Materials Today: Proceedings Volume 4, Issue 2, Part A,  Pages 1285-1292, 2017.  https://doi.org/10.1016/j.matpr.2017.01.149
  • U Ashok kumar, Prof.  P Laxminarayana , “Influence Of Process Parameters On Surface Roughness Of EN31 By Water Jet Machining, Proceedings Of The International Conference On Technological Advances In Mechanical Engineering (ICTAME 2017) On 22nd September 2017 
  • U.Ashok Kumar, Prof. Laxminarayana Pappula , Ramulu M 2 “Tensile Behavior And Microstructural Characteristics Of Friction Stir Welded Butt Joints Of Titanium Alloys” at Proceeding of  Material Science & Technology –October 8-12, 2017,International Conference.

2016 – Publications

  • Jeevan Kumar Naini and Ramesh Babu, P.,” Impact Analysis of Embedded Delamination Location in Hybrid Curved Laminated Composite Stiffened Panel” Applied Composite Materials, Vol .23 No 1(2016)
  • Jeevan Kumar, Ramesh Babu, P. “Analysis of Embedded Delamination Growth in Hybrid Laminated Curved Composite Stiffened Panels” International Journal of Composite Materials 2016, 6(4): 100120
  • Shankarachar Sutar, Radhakrishna Madabhushi and Ramesh Babu, P., Finite Element Analysis of Piping Vibration with Guided Supports, Int. J. Mech. Eng. Autom. Vol. 3 , (2016), 96-106
  • SV Prasad, Dr P Laxminarayana, Dr P Ravinder Reddy “Impact of Cutting Fluids on distortion of 2014A T6 Aluminum alloy during machining”. International Journal of Application or Innovation in Engineering & Management (IJAIEM), Volume 5, Issue 7, pp126-134,July 2016      ISSN 2319 – 4847
  • Mr SV Prasad, P Laxminarayana, P Ravinder Reddy “Evaluation of Machining Induced Residual Stresses in 2014 A T6 Aluminum Alloy Using Indentation Method and its Co-Relation to Distortion due to Tool Path Layouts”, International Journal Of Engineering Sciences & Research Technology,pp 725-737, 2016, ISSN: 2277-9655, DOI: 10.5281/zenodo.51912.
  • D. Raji Reddy, P.Laxminarayana, G.C.M. Reddy, G.M.S.Reddy,"Process Parameters Influence on Impact Toughness and Microstructure of Pre-heat Treated Friction Welded 15CDV6 Alloy Steel", International Journal of Engineering and Manufacturing(IJEM), Vol.6, No.5, pp.38-47, 2016.DOI: 10.5815/ijem.2016.05.05.
  • D Devaiah, K Kishore, P Laxminarayana “Parametric Optimization Of Friction Stir Welding Parameters Using Taguchi Technique For Dissimilar Aluminum Alloys (AA5083 and AA6061)”International Conference on Advanced Material Technologies (ICAMT), Vol.2016, Issue 27 (2016).
  • M Sailender, G Chandra Mohan Reddy, S Venkatesh, N V Srinivasulu; Influences of Submerged Arc Welding Process Parameters on Bead Geometry of low carbon alloy Steel; International Journal on Mechanical Engineering and Robotics (IJMER); ISSN (Print) : 2321-5747, Volume-4, Issue-3,2016;pp 43-50.
  • M. Naveen Kumar, Sriram Venkatesh, M. Manzoor Hussain; Design and Fabrication of Low Cost 3D Printer; International Journal of Scientific Research in Science, Engineering and Technology Vol.3 Issue.3 May-June 2017; P-2395-1990, E-ISSN 2394-4099, IF: 3.632. 
  • Performance Evaluation of Various STL File Mesh Refining Algorithms Applied for  FDM-RP Process; Journal of Institution of India; published by Springer, DOI 10.1007/s40032-016-0303-4; June 2016.

P. S. Ravi, A. Krishnaiah, Md. Azizuddin, Design of Roll Bond Evaporator for Room Air Conditioner using Eco-friendly Refrigerant, R-32 (DiFluoroMethane), International Journal of Innovative Research in Science,Engineering and Technology, Vol. 5, Issue 6, June 2016, 95379543

  • Goitom Tesfaye, Rega Rajendra, Adaptive sampling strategy of Free-form Surface Using CMM. Intl. Conf. on Advanced Materials and Manuf. 2016(ICAMM-2016), Hyderabad, India.(Presented and Published e-ISBN: 978-93-86256-19-5)
  • Boda Hadya.,  “Simulation of Air- Conditioning System Components and Comparison of Performance for Three Different Refrigerants” International Journal of Research in Engineering and Applied Sciences (IJREAS) ISSN  2249-3905, Volume 6, Issue 6, PP.69-76, June 2016
  • Boda Hadya., et al. “Design of Roll Bond Evaporator for Room Air Conditioner using Eco-friendly Refrigerant,R-32 (Difluoro Methane)” International Journal of Innovative Research in Science, Engineering and Technology (IJIRSET) ISSN  2347-6710, Volume 5, Issue 6, PP.9537-9543, June 2016. 
  • Boda Hadya., “Analysis of Vapour Compression Refrigeration System with Sub- cooling and Super Heating with three Different Refrigerants for Air-conditioning Applications” International Journal of Engineering Sciences & Research Technology(IJESRT) ISSN: 2277-9655, volume 5, issue 11, pp.70-77, November, 2016
  • Dr.B.Hadya presented a research paper Title: “Assessment of Energy Efficiency Ratio for Air-Conditioning System for Potential Replacement of R-22”International Conference in Emerging Trends in Mechanical Engineering (ICETiME 16), which is organizing by the ICFAI Foundation for Higher Education during 23rd & 24th September, 2016.
  • BhargaviBaaji, K Saraswathamma, RadhakrishnaMadabhushi, ShankaracharSutar, “Design and Analysis of Spherical Pressure Vessels with Pressure and Thermal Effects” International Journal of Mechanical Engineering and Automation, Vol. 3, No. 6 (2016), 239-248.
  • V. Uma Maheshwar, AMK Prasad, Experimental Investigation of Downstream Flow field  in a Linear Turbine Cascade: Effects of Incidence changes. International Journal of Engineering Technology, Management and Applied Sciences. Volume 4 | Issue10 | Oct  2016
  • L.Siva Rama Krishna. and Kunal Chandana,“ Design Optimization of a Nanosatellite Structure and Prototype Manufacturing Using FDM Rapid Prototyping Process“ National  Conference “Large Scale Multidisciplinary Systems of National  Significance Trends & Challenges” (LAMSYS 2016) organised by ISSE, SDC  SHAR, ISRO,  Sriharikota during 24-25  June, 2016
  • G.Narendar, A.V.S.S Kumara Swami Gupta and A.Krishnaiah, Experimental investigation on Transient State Performance of Natural Circulation Loop. Int. Journal of Engineering Research & Technology, 2016. 5(6): p.15-18.
  • G.Narendar, A.V.S.S Kumara Swami Gupta and A.Krishnaiah, Investigation on Natural Circulation Loop with Nanofluid. Int. Journal of  Engineering Research and Application, 2016. 6(3):  p.53- 58.
  • T.Nagaveni, K.Kishore Kumar, C.S.P.Rao., "Preparation and characterization of Si3N4-BN ceramic composites by Gelcasting‖, Material Science Research India, 13 (1), June 2016. (I.F:0.35)
  • K.Buschaiah, M.Jagadeeswara Rao and M.Chandra Sekhar Reddy “Optimization of Machining Parameter for EDM using Taguchi Method on Incoloy-800”, International Journal of Research in Engineering and Applied Sciences, ISSN:2349-6525,  Vol. 6, Issue 11, pp 119133, November 2016.
  • K.Buschaiah, A.Chandrakanth and S.Gajanana “Experimental Investigation of Metal Removal Rate on EDM for variable Tool Materials”, International Journal of Engineering Sciences & Research Technology, ISSN: 2277-9655, Vol. 5(12), pp 282-286, December 2016.
  • G.Venkateshwarlu, K. Ramesh kumar, T.A.Janardhan Reddy “Experimental Study of  Flowforming Process Parameters on Thickness variation of Aluminum Alloy AA6061 Tubes” International Journal of Latest Research in Engineering and Technology (IJLRET)  ISSN: 2454-5031www.ijlret.com || Volume 02-Issue 10 || October 2016 || PP. 33-40

Previous Publications

  • Shankarachar,S., Radhakrishna,M. and Ramesh Babu, P., Fluid Induced Piping Vibration with Elastically Restrained Different End Supports, International Journal of Engineering Research & Technology, Vol. 4 (2015), 423-429.
  • Garimella Sridhar, Ramesh Babu, P., “ Volume of Material Removal on Distortion in Machining Thin Wall Thin Floor Components” International Journal of Mechanical Engineering and Applications, 2015, 3(5), 86-93.
  • Garimella Sridhar, Ramesh Babu, P., “ Effect of a milling cutter diameter on distortion due rot the machining of thin wall thin floor components” Advances in Production Engineering & Management Jounal, Vol. 10 (3), (2015), 140-152.
  • Ramesh Babu, P. “Evaluation of Flexural and Tensile Properties of Short Kenaf Fiber Reinforced Green Composites” International Journal of Advanced Mechanical Engineering. ISSN 2250-3234 Vol. 4,(2014) , 371-3880.
  • Garimella Sridhar, Ramesh Babu, P.” Cutting Parameter Optimisation for minimizing machining distortion of thin wall thin floor avionic components using Taguchi Techniques”, International Journal of Mechanical Engineering and Technology, Vol. 4 (4), (2013), 71-78.
  • Jeevan  Kumar,  N.,  Ramesh Babu, P. &  Ratnakar  Pandu    “Investigation on Buckling Behaviour of laminated curved composite stiffened panels” Applied Composite Materials, vol 20. (2013)
  • Garimella Sridhar, Ramesh Babu, P. “Understanding the challenges in machining thin walled thin floored Avionics components”, Int. Journal of Applied Sciences and Engineering Research, Vol. 2, (2013), 93-100.
  • Ramesh Babu, P. and Pradhan, B. “Thermoelastic effects on mixed-mode delamination growth emanating from circular holes in laminated FRP composites”, Struct.,82(1) (2008), 50-60.
  • Pradhan, B. Ramesh Babu, P. Influence of ply sequence and thermoelastic stress field on asymmetric delamination growth behaviour emanating from elliptical holes in laminated FRP composites. ASME J. Eng. Mater. Tech., 130(1) (2008).
  • Pradhan, B. and Ramesh Babu, P “ Assessment of beneficial effects of interference-fit in pin-loaded FRP composites”. Reinf. Plast. Compos., 26(8), (2007), 771-788.
  • Ramesh Babu, P. and Pradhan, B., “Effect of damage levels and curing stresses on delamination growth behaviour emanating from circular holes in laminated FRP composites”. Composites Part-AApplied Science and Manufacturing.,,28(12) (2007), 2412-2421.
  • Sriram Venkatesh , “Investigations of the Use of Conical Inserts to Promote Mass-Flow in Bunkers and Silos”, Annual Technical Journal of Advances in Dry Processing; November, 2002; USA.
  • Sriram Venkatesh , “Regression Modelling and Analysis of Design Parameters of Coal Bunkers for Thermal Power Stations; Bulk Solids Handling”, The International Journal of Storing Handling and Transporting Bulk Vol.22, June 2002, No.5, Germany, and pp. 426 - 429.
  • Sriram Venkatesh , “Silo Quaking –The Phenomenon of Self-Excited Flow-Induced Vibrations In Bunkers And Silos; Bulk Solids Handling”, The International Journal of Storing Handling and Transporting Bulk Vol.23, (2003), No.4, GERMANY, pp. 258-261.
  • Sriram Venkatesh , “Design of Mass Flow Silos for grain storage, International Journal on Bulk Solids & Powder Science & Technology”, Vol.29, (2009), No.3, GERMANY, pp. 158-162.
  • Sriram Venkatesh , “Multi Objective Job shop Scheduling using Hybrid differential Evolution     Approach DOI 2011”, International Journal of Advanced Operations Management (Accepted on 7th Sept. 2010) ISSN Online 17589398 Print version 1758938X
  • Sriram Venkatesh , “Experimental Optimization of Roller Burnishing Process Parameters and validation check by DOE” International journal of Optimization and Engineering (OPTE) ISSN: 1389-4420 (in press)
  • Sriram Venkatesh , “Harmonic Analysis Of Mass-Flow Bunkers And Silos With Reference To Thermal Power Plants, Bulk Solids Handling”, The International Journal of Storing Handling and Transporting Bulk (Under Review)
  • L. Siva Rama Krishna, Manmadhachary, P. Bal Reddy, Sriram Venkatesh;     Development of optimum preplanning for maxillofacial surgery using selective laser    sintering; International Journal of Engineering, Science and Technology;Vol. 3, No. 8, 2011, pp. 185-196
  • Hameeda Sahib Hasan and Sriram Venkatesh,Design and Development of Prototype Mobile Robot for identification of Deffects in Pipelines, International Journal of Mechanical Engineering and Robotics Research,Hyderabad ,India, Vol 2, No.4, October, 2013., ISSN 2278-0149
  • M.Sailender, Dr.N.V.Srinivasulu, Dr.Sriram Venkatesh, Dr. G C M. Reddy:     “Experimental Analysis of Effect of Various Parameters in Temperature Distribution in Submerged Arc Welding”- International Journal of Engineering and Innovative Technology (IJEIT), Volume 2, Issue 2, August 2012, ISSN: 2277-3754.
  • L. Siva Rama Krishna, Sriram Venkatesh, M. Sastish Kumar, M. Uma Maheswara    Chary A Comparative Study on the Dimensional Error of 3D CAD Model and SLS      RP Model for Reconstruction of Cranial Defect; World Academy of Science,      Engineering and TechnologyInternational Journal of Mechanical, Industrial Science    and Engineering Vol:8 No:3, 2014
  • S.H.Rahul, K.Balasubramanian, Sriram Venkatesh, “Inkjet Printing for fabrication of  porous films”, International Journal on Mechanical Engineering and Robotics (IJMER),Vol.3,No.3,pp.1-6,2015. [Impact. Factor=1.95(ISI)]; DOI: 10.1453/IJMER/128     
  • S.H.Rahul, K.Balasubramanian, Sriram Venkatesh, Inkjet Printing of Yttria    Stabilised Zirconia Nano Particles on Metal Sbstrates,International Journal of   Precesion Engineering and Manufacturing, Vol.16, No. 12, 
  • P.S.Ravi, Arkanti Krishnaiah, Suresh Akella, Md. Azizuddin, Design of Roll Bond Evaporator for Room Air Conditioner, International Journal of Engineering Research & Technology (IJERT), Vol. 4 Issue 11, (2015), 315-320.
  • P.S.Ravi, Arkanti Krishnaiah, Suresh Akella, Md. Azizuddin, Evaluation Of Inside Heat Transfer Coefficient of Roll Bond Evaporator for Room Air Conditioner, International Journal of Innovative Research in Science, Engineering and Technology, Vol. 4, Issue 5, (2015), 3378-3384. 
  • S. Ferhathullah Hussainy, M. Viquar Mohiuddin, P. Laxminarayana,  A. Krishnaiah, S. Sundarrajan, A Practical Approach to Eliminate Defects in Gravity Die Cast Al-Alloy Casting Using Simulation Software, International Journal of Research in Engineering and Technology, Volume: 04 Issue: 01, (2015).
  • Siva Prasad Arikatla, K.Tamil Mannan and Arkanti Krishnaiah, Experimental Investigations on Kerf width and Material Removal Rate in Wire Electric Discharge Machining of Titanium Alloy, International Journal of Emerging Research in Management & Technology (IJERMT),  Vol. 4, Issue 11, 2015. 
  • M. Viquar Mohiuddin, A. Krishnaiah, S. Ferhathullah Hussainy, Effect of Composition of Sand Mold on Mechanical Properties and Density of Al-Alloy Casting Using Taguchi Design Approach, International Journal of Engineering Research and Application, ISSN : 2248-9622, Vol. 5, Issue 3, (2015), pp.37-41.
  • M. Viquar Mohiuddin, A. Krishnaiah, S. Ferhathullah Hussainy, Influence of Sand Molding Process Parameters on Product Quality of Al-Si Alloy Casting - An Anova Approach, Published in International Journal of Advance Research in Science and Engineering, ISSN-2319-8354(E), Vol. 4, Special Issue (01), (2015), pp. 1751-1760.
  • Mohammed Viquar Mohiuddin, Syed Ferhathullah Hussainy, A. Krishnaiah, P. Laxminarayana and S. Sundarrajan, Experimental Study of Sand Mold Process Parameters on Al-Alloy Sand Casting using DoE, ISOR Journal of Mechanical and Civil Engineering, Volume 11, Issue 6, (2014), pp. 01-06.
  • Ganesh B.K.C, W. Sha, N. Ramanaiah, Arkanti Krishaniah,  Effect of Shot Peening on Sliding Wear and Tensile Behavior of Titanium Implant Alloys, International Journal of Materials & Design, Volume-56, April (2014), Pages 480-486. 23. Narender G, Arkanti Krishaniah, N.V.S.S Gupta, Experimental Investigation on Natural Circulation Loop with Different States of Loop Fluid at the Starting of Activation of the Circulation Loop, International Journal of Engineering Research & Technology, Vol. 3 Issue 11, November-(2014), 456-1459.
  • Chandrakanth Achelker, N. Srinivasa Rao, R. Rajendra, Arkanti Krishaniah, Performance Evaluation of Machine Tool Probe for In-process Inspection of 2D and 3D Geometries, International Journal of Procedia Technology, Volume-14 (2014), 244–251.
  • Siva Prasad Arikatla, Arkanti Krishnaiah and K.Tamil Mannan, Optimization of Electric Discharge Machining Response Variables using Design of Experiments, International Journal of Mechanical and Production Engineering, Volume-2, Issue-1, (
  • K.Tamil Mannan, Arkanti Krishnaiah and Siva Prasad Arikatla, “Surface Characterization of Electric Discharge Machined Surface of High Speed Steel” International Journal of Advanced Materials Manufacturing and Characterization, IJAMMC, ISSN No. : 2277 – 3886, p no 161-168, Vol 3, Issue 1, 2013.  
  • Siva Prasad Arikatla, K.Tamil Mannan & Arkanti Krishnaiah, Investigations on Surface Characterization of Wire Electric Discharge Machined Surface of Titanium Alloy, International Journal of Engineering Research and Tech., IJERT, ISSN No. : 0974-3154, p no 773-780, Vol. 6, No. 6, 2013. 
  • Siva Prasad Arikatla, Arkanti Krishnaiah and K.Tamil Mannan, Analysis of White Layer and Heat Affected Layer in Electric Discharge Machined Surface of AISI T1 High Speed Steel International Journal of Composites Materials and Manufacturing, IJCMM, ISSN No. : 2249 – 4030, p no. 1-7, Vol 1, Issue 1, 2013.
  • Siva Prasad Arikatla, K.Tamil Mannan and Arkanti Krishnaiah, “Influence of Pulse Current & Pulse on Time on MRR and Surface Roughness in Electric Discharge Machining of AISI T1 HSS”, Advances in Engineering and Technology Series 03, ACEEE, ISSN: 2214-0344.
  • M. Ramulu, DVR Murty and A. Krishnaiah, The Study of Plastic Deformation behaviour of IF Steel during Equal Channel Angular Pressing through 120° die angle by FEM, IJNT: Volume 3, Number 2, (2012) 49-53. 31. G. Mrudula, B. Srinivasulu and A. Krishnaiah, Investigation on Mechanical and Microstructural Behaviour of Friction Stir Weldments of ZE42 Magnesium Alloy, International Journal of Emerging Technology and Advanced Engineering, Volume 2, Issue 8, (2012) 190-197. 
  • H. J. Jeong, A. Krishnaiah, S. C. Yoon, U. Chakkingal, S.Y. Kang and Hyoung Seop Kim, Finite Element and Experimental Analyses of Repetitive Bending and Straightening of Commercially Pure Copper, Reviews on Advanced Materials  Science 28 (2011) 79-84.
  • Krishnaiah, K. Kumaran and Uday Chakkingal, Finite Element Analysis of Multi-Pass Equal Channel Angular Extrusion/Pressing Process, Material Science Forum, 654-656 (2010) 1574-1577.
  • Pham Quang, A. Krishnaiah, Sun Ig Hong and Hyoung Seop Kim, Coupled Analysis of Heat Transfer and Deformation in Equal Channel Angular Pressing of Al and Steel, Materials Transactions, 50 (2009) 40-43.
  • Seung Chae Yoon, A. Krishnaiah, Uday Chakkingal and Hyoung Seop Kim, Severe Plastic Deformation and Strain localization in Groove Pressing, Computational Materials Science, 43 (2008) 641-645.
  • Krishnaiah, Uday Chakkingal and Hyoung Seop Kim, Mechanical Properties of Commercially Pure Aluminium Subjected to Repetitive Bending and Straightening Process, Transactions of Indian Institute of Metals, 61(2008) 1-3. 
  • Seung Chae Yoon, Min Hong Seo, A. Krishnaiah, Hyoung Seop Kim, Finite element analysis of rotary-die equal channel angular pressing, Materials Science & Engineering A, 490 (2008) 289292.
  • Krishnaiah, Uday Chakkingal and P. Venugopal, Microstructure and Mechanical Properties of Commercial Purity Copper Resulting from Repeated Groove Pressing Followed by Cold Rolling. Material Science Forum, 539 (2007) 2198-2203.
  • Krishnaiah, Uday Chakkingal and P. Venugopal, Microstructure and Mechanical Properties Resulting from Cold Rolling of Equal Channel Angular Extruded Commercial Purity Copper. Material Science Forum, 503 (2006) 733-738. 
  • Krishnaiah, Uday Chakkingal and P. Venugopal, Applicability of the Groove Pressing Technique for Grain Refinement in Commercial Purity Copper. Material Science and Engineering A, 410 (2005) 337-340. 
  • Krishnaiah, Uday Chakkingal and P. Venugopal, Production of Ultrafine Grain Sizes in Aluminium Sheets by Severe Plastic Deformation Using the Technique of Groove Pressing. Scripta Materialia, 52 (2005) 1229–1233.
  • B.Hadya., et al. Presented paper entitled: “A comparative Study on the performance and Environmental Impact of Alternate refrigerants to Replace R-22”, RITS International Conference on Advancements in Engineering & Management (ICAEM-2012).
  • B.Hadya., et al. Presented paper entitled: “Performance Evaluation of R32 as Retrofit Refrigerant in Existing Air Conditioners in Indian Scenario”, National Conferences on Recent Advances in Mechanical Engineering   RAME-2012.
  • B.Hadya., et al. Presented paper entitled:“Comparative Study of Eco-friendly Refrigerants in a Lower Capacity Air-Conditioning System”, International Conference (ICMAE- 2012)   ISBN. 978-93-82242-07-09 (PP: 48-51) (Awarded Session Best Paper).
  • B.Hadya. et al. Presented paper entitled: “Flow Characteristics of a Refrigerant inside a Diabetic Capillary Tube with Suction line Heat Exchanger”, International Conference of (CAFE-2012).
  • B.Hadya., et al. Presented paper entitled: “Simulation of Air – Conditioning System and Transport Properties for Alternative Refrigerants”, RITS 2nd International Conference on Advancements in Engineering & Management (ICAEM-2013) ISBN 978-93-5104-586-1(PP: 446-450).
  • B.Hadya,  “CFD Analysis on Double pipe helical coil heat Exchange. RITS ICAEM 27 &28   Feb.2013ISBN 978-93-5104-586-1, PP: 442-445.B.Hadya.,et al. “Analysis of Transport Properties for Hydro Fluorocarbon (HFCS) Refrigerant for Air –Conditioning system”, International Journal of Advanced Research in Engineering and Technology (IJARET-2013)  ISSN 0976 – 6480,  Volume 4, Issue 3,  pp. 163-169, April 2013
  • B.Hadya., et al “Theoretical Analysis and Performance Comparison of Different Alternative Refrigerants to HCFC-22”,International Journal of Scientific &Engineering Research,  (IJSER)Volume No 5,Issue 5, ISSN  2229-5518 , pp1505-1508, May-2014 .
  • B.Hadya. et al., “Simulation of Air-Conditioning Compressor with Different Refrigerants and to Retrofit in Existing (HCFCs-22) Air-Conditioning Systems”, International Journal of Thermal Technologies (IJTT) ISSN 2277-4114, Vol.4, No.2, pp: 83-87.  June -2014.
  • B.Hadya., et al. “Experimental Evaluation of Environmental Friendly and Low Global Warming Refrigerants as an Alternative Option for Window Air Conditioning System”, Journal of Refrigeration, Air-conditioning, Heating and Ventilation (JoRACHV) ISSN2394-1952, Volume 1, Issue 3, PP.7-13, September-December 2014.
  • B.Hadya, et al. “Performance Assessment of HFC Group Refrigerants in Window Air Conditioning System, in the International Journal of Mechanical Engineering and Applications (IJMEA) ISSN 2330-0248, Vol 3, issue 5,pp;81-85,  Science Publishing Group, USA, August 2015.
  • K.Saraswathamma, “Magnetorheological finishing: A Review” International Journal of Current Engineering and Technology, Special Issue-2, (February 2014), 168-173.
  • K.Saraswathamma, Sunil Jha, P.V. Rao “Design of Parallel Plate Magnetorheometer for evaluation Rheological properties of Magnetorheological polishing fluid”, Materials Today: Proceedings 2 (2015) 3251 – 3259.
  • K Saraswathamma, Sunil Jha, P.V. Rao “Rheological characterization of MR polishing fluid for Si polishing” Materials and Manufacturing processes, Vol. 30, issue 5, (2015) 661668.
  • K Saraswathamma, Sunil Jha, P.V. Rao “Experimental Investigation into Ball End Magnetorheological Finishing of Silicon” Precision Engineering, Vol. 42 (2015), 218-223.
  • M.V.Ramana Murthy, “A Review of New Technologies, Models and Experimental Investigations of Solar Driers “an Elsevier Publication appeared in volume 13 Issue 4, 2009.
  • M.V.Ramana Murthy, “An Analysis and an example to correlate an individual to the society for environment protection, practice of energy conservation tips and adaptation of renewable energy sources.” World Renewable Energy Congress, Linkoping University, Sweden, May 8 to 13, 2011.
  • Md. Abdul Raheem Junaidi,GM Sayeed Ahmed, Dr. Nawazish Mehdi, V. Uma Maheshwar, Design Optimisation and Analysis of a Steam Turbine Rotor Grooves, IOSR Journal of Mechanical and Civil Engineering, Vol 8,Issue 6, PP 66-72
  • L.Siva Rama Krishna, Sriram Venkatesh , M.Satish Kumar., M.Umamaheshwara Chary., “A Comparative Study on the Dimensional Error of 3D CAD Model and SLS RP Model for Reconstruction of Cranial Defect“, International Journal of Mechanical, Aerospace, Industrial, Mechatronic and Manufacturing Engineering Vol:8, No:3, 2014, ISSN No. 2010376X(Print) 20103778 (Print) (2047 Downloads) Cited in Springer open journal on 3D Printing in Medicine (2015) 1:2DOI 10.1186/s41205-015-0003-3).
  • S.Gajanana, L.Siva Rama Krishna, Srinivas Rao Nandam, B.K.Mohan, “Optimization of process parameters of End Milling process using factorial design of experiments”,  Manufacturing Technology Today Journal Vol. 12, No.6, June 2013, pp. 05-13 ISSN No. 0972-7396.
  • L. Siva Rama Krishna, Manmadhachary, P. Bal Reddy, Sriram Venkatesh, “Development of optimum preplanning for maxillofacial surgery using selective laser sintering” International Journal of Engineering, Science and Technology Vol. 3, No. 8, 2011, pp. 185-196, ISSN No.2141-2839. DOI:10.4314/ijest.v3i8.16.
  • V. Mahesh, L. Siva Rama Krishna, Sandeep Dulluri, C. S. P. Rao, “Theoretical Analysis on Powers-of-two Applied to JSP – A Case Study of Turbine Manufacturing”, the International Journal of Green Computing Vol. 2, No.2, July-December 2011, pp.1-20.ISSN No. 1948-5018. DOI: 10.4018/IJGC
  • L. Siva Rama Krishna, V. Mahesh, Sandeep Dulluri, C. S. P. Rao, “Implementation of an online scheduling support system in a high mix manufacturing firm“, International Journal of Engineering, Science and Technology Vol. 2, No. 11, 2010, pp. 90-103, ISSN No.2141-2839.
  • L. Siva Rama Krishna G.Ranga Janardhan C.S.P Rao, “A Real Time Web Integrated Scheduling Support System for A Multi Product Manufacturing Industry”, International Journal of The Computer, The Internet And Management (IJCIM), Vol.17, No.2, pp.55-68, August 2009. ISSN No. 0858-7027.
  • L.Siva Rama Krishna, G.Ranga Janardhan, C.S.P Rao, “Development of an Online Supplier Selection System for a Turbine Manufacturing Company” 19th International Conference on Flexible Automation and Intelligent Manufacturing (FAIM 2009) organized by University of Teesside,  Middlesbrough, UK from  6-8 July, 2009.
  • L.Siva Rama Krishna., G..Rangajanardhan, C.S.P Rao,“ Development of An Integrated Material Planning And Machine Scheduling System for a Multi Product Manufacturing Industry“ 22nd International Conference on “CAD/CAM Robotics and Factories of the future”, organized by International Society for Productivity Enhancement (ISPE), Vellore Institute  of Technology, Vellore,  19th to 22nd July, 2006.ISBN No. 13:978-81-7319-792-5
  • L.Siva Rama Krishna., G..Rangajanardhan, Sandeep Dulluri, C.S.P Rao,“ Web Integrated Inventory and Machine Scheduling Decision Support System for a Multi Product Manufacturing Industry “ International Conference on “e-Manufacturing: An emerging Need for 21st century World – Class enterprises”, organized by Institution of Engineers (India) M.P. State Centre, M.A.N.I.T Bhopal, 17th to 19th November, 2002. ISBN No. 81-7484-066-4.
  • L.Siva Rama Krishna., G..Rangajanardhan, C.S.P Rao, “A web Integrated Scheduling Support System for a Multi Product Manufacturing Industry” 30th International Conference on “Computers and  Industrial Engineering”, organized by University of Aegean, Greece,  29th June to 2nd July, 2002.ISBN No. 960-431-790-3.
  • V.Mahesh, L.Siva Rama Krishna, D.Sandeep, CSP Rao, “ Design and Development of a Database oriented Scheduling System for a Multi Product Manufacturing Industry”, 2nd International conference on Responsive Manufacturing, organised by Dept. of Industrial Engineering, Faculty of Engineering,  University of Gazientep, Turkey during 26-28 June 2002.
  • Mohand Mosa Mohammad, G.Narendar, Design and Heat Transfer Analysis of a Parabolic Shaped Solar Dish Collector, International Journal & Magazine of Engineering, Technology, Management and Research(ISSN No: 2348-4845 ), 2015. Volume No: 2 (2015), Issue No: 7, P. 168-173
  • T.Nagaveni, C.S.P.Rao, ―Development of Silicon Nitride-Based Ceramic Radomes  A Review‖, International Journal of applied ceramics technology, 12: 909–920 (2015). DOI: 10.1111/ijac.12305( Impact factor: 1.165).
  • K.Buschaiah, P.Laxminarayana and V.S.R.Murti “Some Anomalies in the Experimental Results of EDM”, International Journal of Manufacturing Technology and Management, Vol. 24, Nos. 1/2/3/4, pp 57-70, 2011.
  • K.Buschaiah, P.Laxminarayana and V.S.R.Murti “Some Anomalies in the Experimental Results of EDM”, International Journal of Manufacturing Technology and Management, Vol. 24, Nos. 1/2/3/4, pp 57-70, 2011.
  • K.Buschaiah, A.Parshuramulu and P.Laxminarayana “Integrity of EDMed Job Surfaces”, International Journal of Advances in Management,Technology & Engineering Sciences, ISSN:2249-7455,  Vol. II, Issue 7(I), pp 15-19, April 2013.
  • A.Parshuramulu, K.Buschaiah, and P.Laxminarayana “A Study on Influence of Polarity on the Machining Characteristics of Sinker EDM”, International Journal of Advanced Research in Engineering and Technology (IJARET), ISSN: 0976-6480, Vol. 4, Issue 3, pp 158-162, April 2013.
  • G Venkateshwarlu, K Ramesh kumar, T A Janardhan Reddy, G. Gopi Study on the Mechanism of Flow forming: A Review “2nd International Conference on Advancements in Engineering& Management”(2012)
  • G Venkateshwarlu, K Ramesh kumar, A.M.K.Prasad, T.A.Janardhan Reddy, “Evaluation of Mechanical Properties of Aluminum Alloy AA 6061(HE-20)” 1st International Conference on Advances in Mechanical Sciences (2014).
  • K.Saraswatamma, G Venkateshwarlu, P.Venkatrami Reddy, ” Optimization of surface roughness in the roller burnishing process using RSM&D.F” International Conference on Emerging Trends in Mechanical Engineering (ICEME-2014).
  • G.Venkateshwarlu, K. Ramesh kumar, T.A.Janardhan Reddy “Estimation of the Grain size number and Microstrucrure analysis of AA6061 alloy flow formed tubes” International Conference on Emerging Trends in Engineering (ICETE) March 2019 || PP. 136
  • G. Venkateshwarlu, K. Ramesh kumar, T. A. Janardhan Reddy, G. Gopi,. “Study on the Mechanism of Force Calculations on Flow Forming”: A Review “International Journal of Engineering Science and Innovative Technology”. (IJESIT). (2012)
  • G. Venkateshwarlu, K. Ramesh kumar, T. A. Janardhan Reddy, G. Gopi.,. “Study on the Mechanism of Flow Forming: A Review”. “International Journal of Engineering Science and Innovative Technology”. (IJESIT). (2012)
  • G.Venkateshwarlu, K. Ramesh kumar, T.A.Janardhan Reddy, G.Gopi. “Experimental Investigation on Spinning of Aluminum Alloy 19500 Cup” International Journal of Engineering Science and Innovative Technology (IJESIT) Volume 2, Issue 1, January 2013. Journal Impact Factor (2013): 6.0 (Calculated by GISI) (2013)
  • G Venkateshwarlu, K Ramesh kumar, T. A. Janardhan Reddy, G. Gopi, “Study on the Mechanism   of Force Calculations in Flow forming”: A Review International Journal of Advanced Research In Engineering And Technology (IJARET) Volume 4, Issue 3, April 2013, pp. 194-201 . Journal Impact Factor (2013): 5.8376 (Calculated by GISI) (2013)
  • G Venkateshwarlu, K Ramesh kumar,  A.M.K.Prasad, T.A.Janardhan Reddy, Evaluation of Mechanical Properties of Aluminum Alloy AA 6061(HE-20) International Journal of Current Engineering and Technology. ISSN 2277 – 4106 (2014)
  • K.L.Uday Kiran, G.Chandramohan Reddy , A.M.K.Prasad and R.Rajendra, “ Study of Surface integrity Characteristics on Al and Die Steel Components using Copper tool in Sink EDM Process”,  International Journal of Current Engineering and Technology E-ISSN 2277 – 4106, P-ISSN 2347 – 5161.
  • K.L.Uday Kiran, R.Rajendra, G.Chandramohan Reddy, A.M.K Prasad, “Comparative Study on Variation of Process Characteristics on Al And Die Steel Components In Sink EDM Process”, International Journal Of Advanced Research In Engineering And Technology (IJARET), Volume 4, Issue 3, April 2013, pp. 170-177.
  • K.L.Uday Kiran, G.Chandramohan Reddy , A.M.K.Prasad and R.Rajendra, “Effect of Current on Surface Roughness Parameters and MRR in Sink EDM Process”, 2nd International Conference on Advancements in Engineering And Management, RITS ICAEM-2013.
  • M.Prakash, “Analysis and Fabrication of a Butt Joint Using Friction Stir Welding”, Published in proceedings of ICMIE2014, 30th March 2014, Chennai, India – ISBN: 978-3-642-24819-8, pp. 103-108.
  • M Prakash, “Analysis and Fabrication of a Butt Joint Using Friction Stir Welding”, Published in International Journal on Mechanical Engineering and Robotics (IJMER), SSN (Print): 2321-5747, Volume-2, Issue-1, 2014, pp. 37-42.
  • M Prakash, “Characterisation of Aluminium over Mild Steel by Friction Surface Processing”, Published in International Conference on Emerging Trends in Engineering and Management (ICETEM 2013) – WARSE Publishers 2013, pp. 61-63.
  • M Prakash, “Experimental and Characterisation of Aluminum over Mild Steel by Friction Surface  Processing”, published in International Conference on Research and innovations in Mechanical Engineering 2013 Proceedings of the International Conference on Research and Innovations in Mechanical Engineering, Lecture Notes in Mechanical Engineering, DOI: 10.1007/978-81-322-1859-3_35,  Springer India 2014,pp 375-381.
  • M Prakash, “Experimental and Characterisation of Aluminum Over Mild Steel by Friction Surface Processing”, published in Proc. 2013 FIME NationalConf., 2013, pp.179-181.
  • M Prakash, “Friction stir welding: An Green Environmental Process ”, Published at 4th International & 25th All India Machine Tool Design and Research Conference - 2013 (AIMTDR) held at Jadavpur University, Kolkata